Provide Kees Model KS-100 wall hung (or KSI-100 island style) energy saving hood(s) constructed of 18 gauge (or 16 gauge) type 304 stainless steel having a #3 polish. Hood(s) shall be double wall type capable of providing untempered make-up air into the internal hood capture area through adjustable rotatable supply air nozzles. Nozzles shall be capable of being locked in position after balancing. Untempered air being introduced into the hood shall first encounter a perforated stainless plate to spread the air across the full length of the air plenum before entering the adjustable rotatable stainless outlet nozzles. The hood supply air plenum shall be completely lined with 1 inch thick 3# density U.L. listed foil faced rigid insulation having a flame spread of 25 or below with a full length perforated metal air distribution plate inside the air plenum. Joints in insulation shall be sealed with aluminum thermal tape. Bottom of the supply plenum shall be lined with galvanized steel to facilitate cleaning. End panels shall be 1 inch thick insulated double wall construction to prevent condensation on end walls. Hanger brackets shall be provided on each corner of hod and threaded to accept 1/2 inch rod. Additional hangers shall be provided on hoods over 132 inches in length. All exterior seams shall be continuously welded, liquid tight as required by U.L., and ground and polished to match the original finish of the material. Hood(s) shall be fabricated in accordance with National Fire Protection Association (NFPA) Bulletin No. 96, shall be National Sanitation Foundation (NSF) Listed an bear the NSF seal, and shall be Underwriters Laboratories (U.L.) Listed an U.L. labeled as required. U.L. Listed exhaust air fire dampers shall be provided if required by local code. Hood shall include a U.L. Listed fire damper for each supply collar. The full length filter housing with pitched grease trough shall be of 18 gauge, type 304, #3 polish stainless steel complete with removable stainless steel grease container. Filters shall be U.L. Classified, 2" thick baffle type constructed of aluminum (or stainless steel). Lights shall be U.L. Listed incandescent vapor proof 100 watt type on approximately 3 foot centers (or U.L. Listed fluorescent fixtures) pre-wired to a junction box on top of the hood. Wiring shall conform to the National Electric Code (NEC). For more details, refer to KEES catalog KSSC.

Energy Saving Model S-W

Provide KEES Model S-W wall hung (or S-W island style) combination energy saving short cycle untempered air hood and kitchen untempered ventilation system. Hood to be of 18 gauge (or 16 gauge) type 304 stainless steel having a #3 polish. Hood(s) shall be double wall type capable of providing either untempered make-up air into the internal hood capture area through patented adjustable rotatable supply air nozzles or into the room through double deflection clear anodized extruded aluminum grilles installed on the hood face with change over accomplished with push-pull insulated face operated dampers. The adjustable nozzles are of stainless steel construction and can be locked in position after balancing. The hood supply air plenum shall be completely lined with 1 inch thick 3# density U.L. Listed foil faced rigid insulation having a flame spread of 25 or below with a full length perforated metal air distribution plate inside the air plenum. Joints in insulation shall be sealed with aluminum thermal tape. Bottom of the supply plenum shall be lined with galvanized steel to facilitate cleaning. Supply plenum shall be provided with U.L. Listed fire damper as required by U.L. and NFPA-96. End panels shall be 1 inch thick insulated double wall construction to prevent condensation on end walls. Hanger brackets shall be provided on each corner of hood and are threaded to accept 1/2 inch rod. Additional hangers will be provided on hoods over 132 inches in length. All exterior seams shall be continuously welded, liquid tight as required by U.L., and ground and polished to match the original finish of the material. Hood(s) shall be fabricated in accordance with National Fire Protection Association (NFPA) Bulletin No. 96, shall be National Sanitation Foundation (NSF) Listed an bear the NSF seal, and shall be Underwriters Laboratories (U.L.) Listed an U.L. labeled as required. U.L. Listed exhaust air fire dampers shall be provided if required by local code. Hood shall include a fire damper for each supply collar. The full length filter housing with pitched grease trough shall be of 18 gauge, type 304, #3 polish stainless steel complete with removable stainless steel grease container. Filters shall be U.L. Classified, 2" thick baffle type constructed of aluminum (or stainless steel). Lights shall be U.L. Listed incandescent vapor proof 100 watt type on approximately 3 foot centers pre-wired to a junction box on top of the hood. (or U.L. Listed fluorescent fixtures). Wiring shall conform to the National Electric Code (NEC). For more details, refer to KEES catalog SWH.

Energy Saving Retro-fit Hood Series 34

Provide KEES Series 34 kitchen retro-fit hood to convert the exhaust hood to a short-cycle system by introducing the untempered outside directly into the hood through adjustable rotatable 304 stainless steel nozzles. The retro-fit hood shall be constructed of 304 polished stainless (or painted galvanized steel) (or unpainted galvanized steel) and lined with 1 inch of 3 lb. rigid aluminum foil faced insulation with all exposed edges covered with heat sealed aluminum foil tape. The unit shall include a full length perforated plate in the plenum, air straighteners in the outlet nozzles and nozzle locking nuts. For more details, refer to KEES catalog RFH.

Exhaust Only Kitchen Hood Model KA & KB

Provide KEES Model KA wall hung (or KB island style) exhaust only hood(s) constructed of 18 gauge (16 gauge) type 304 stainless steel having a #3 polish of sizes as indicated. All exterior seams shall be continuously welded, liquid tight as required by U.L., and ground an polished to match the original finish of the material. Hood(s) shall be fabricated in accordance with National Fire Protection Associated (NFPA) Bulletin No. 96, shall be National Sanitation Foundation (NSF) Listed and bear the NSF seal, and shall be Underwriters Laboratories (U.L.) Listed and U.L. labeled as required. U.L. Listed exhaust air fire dampers shall be provided if required by local code. The full length filter housing with pitched grease trough shall be of 18 gauge, type 304, #3 polish stainless steel complete with removable stainless steel grease container. Filters shall be U.L. Classified, 2" thick baffle type constructed of aluminum (or stainless steel). Lights shall be U.L. Listed incandescent vapor proof 100 watt type on approximately 3 foot centers (or U.L. Listed fluorescent fixtures) pre-wired to a junction box on top of the hood. Wiring shall conform to the National Electric Code (NEC). For more details, refer to KEES catalog KAB.

Exhaust only moisture or heat only hoods Model KG

Provide KEES Model KG exhaust only moisture (or heat only) hood(s) constructed of 18 gauge type 304 stainless steel with #3 polish (or .063" mill finish aluminum) of sizes as indicated. All exterior seams shall be continuously welded, liquid tight, and ground and polished to match the original finish of the material. Moisture hood(s) shall include a full perimeter condensate gutter with welded drain fitting. Heat only wall (or island) hood(s) shall have offset hemmed front (or front and rear) edge(s) for stiffness. Hood(s) shall be National Sanitation Foundation (NSF) Listed and bear the NSF seal. For more details, refer to KEES catalog KFG.

Exhaust only high moisture hood Model KF

Provide KEES Model KF exhaust only high moisture hood(s) constructed of 18 gauge type 304 stainless steel with #3 polish of sizes as indicated. All exterior seams shall be welded, liquid tight, and ground and polished to match the original finish of the material. The hood(s) shall include a full perimeter condensate gutter, welded drain fitting, and removable pitched condensate baffles. Hood(s) shall be National Sanitation Foundation (NSF) Listed and bear the NSF seal. For more details, refer to KEES catalog KFG.

Exhaust only backshelf kitchen hood Model KC, KD, and KE

Provide KEES Model KC (or KD) (or KE) exhaust only backshelf (or backshelf/counter) (or broiler/oven or pizza) type hood(s) constructed on 18 gauge type 304 stainless steel with #3 polish of sizes as indicated. All exterior seams shall be continuously welded, liquid tight, and ground and polished to match the original finish of the material. The filter housing and full length pitched grease trough shall be of 18 gauge type 304 #3 polish stainless steel with removable stainless steel grease container. Filters shall be U.L. Classified, 2" thick baffle type constructed of aluminum (or stainless steel) and shall be of full hood length and of height to assure optimal performance as specified by the filter manufacturer. Hood(s) shall be fabricated in accordance with National Fire Protection Association (NFPA) Bulletin #96, and shall be National Sanitation Foundation (NSF) Listed and bear the NSF seal. For more details, refer to KEES catalog KCDE.

Tempered Air Hoods Models KS-200T, KS-300T, KS-400T

Provide KEES Model KS-200T (or 300T) (or 400T) wall hung canopy (or KSI-200T (or 300T) (or 400T) island canopy) constructed of 18 gauge (or 16 gauge) type 304 stainless steel having a #3 polish of sizes as indicated. Seams shall be continuously welded, liquid tight as required by U.L., and ground and polished to match the original finish of the material. Hood(s) shall be fabricated in accordance with National Fire Protection Association (NFPA) Bulletin No. 96, shall be national Sanitation Foundation (NSF) Listed and bear the NSF seal, and shall be Underwriters Laboratories (U.L.) Listed and U.L. labeled as required. U.L. Listed supply air fire dampers shall be supplied as required by local code. The full length filter housing with pitched grease trough shall be of 18 gauge, type 304, #3 polish stainless steel complete with removable stainless steel grease container. Filters shall be U.L. Classified, 2" thick baffle type constructed of aluminum (or stainless steel). The hood shall be capable of introducing up to 90% of exhausted air with outside tempered air. Clear anodized extruded aluminum supply registers shall be capable of delivery without excess draft by utilizing two sets of adjustable deflection blades together with a face operated opposed blade damper. Lights shall be U.L. Listed incandescent vapor proof 100 watt type on approximately 3 foot centers (or U.L. Listed fluorescent fixtures) pre-wired to a junction box on top of the hood. Wiring shall conform to the National Electric Code (NEC). For more details, refer to KEES catalog KST.